User Manual Q&AAnswer
Feb 25, 2025 - 09:51 PM
To disassemble the Acer VG270U LCD monitor, follow these steps:
1. Prepare the necessary tools, including a working table, Philips-head screwdriver, Hex-head screwdriver, knife, glove, cleaning cloth, and ESD protection.
2. Clean the room and identify the area for disassembling the monitor.
3. Start by disassembling the RC, stand, and base. Unlock the center xxxx of the RC, then remove the RC from the monitor and extract the FFC CTRL from the IF BD.
4. Disassemble the CTRL BD by tearing off the adhesive tape of the FFC CTRL from the RC and removing the CTRL BD from the RC.
5. Disassemble the SPK and lamp wire by tearing off the tapes of the SPK wire, extracting the SPK wire from the IF BD, and disassembling the SPK from the MF. Also, tear off the black tape of the lamp wire and extract it from the P/BD.
6. Disassemble the ASSY TRIM by unlocking the two TRIM screws and removing the ASSY TRIM from the MF. Then, disassemble the LED BD from the Trim and extract the LED wire from the LED BD.
7. Disassemble the SHD and MF by tearing off the conductive tapes and Kapton tapes on the FFC wires. Extract the FFC wires from the panel and unlock the screws from the MF to remove it from the panel. Also, extract the lamp wire from the panel.
8. Disassemble the I/F BD and P/BD by unlocking the PCBA screws from the PCBA BD, DP xxxx , and grounded xxxx . Remove the I/F BD from the SHD, extract the P/BD wire and FFC LVDS from the I/F BD, and remove the P/BD from the SHD.
To assemble the Acer VG270U LCD monitor, follow these steps:
1. Prepare the necessary tools, including a working table, Philips-head screwdriver, Hex-head screwdriver, knife, glove, cleaning cloth, and ESD protection.
2. Clean the room and identify the area for assembling the monitor.
3. Start by assembling the I/F BD and P/BD to the SHD. Insert the P/BD wire to the P/BD and assemble the P/BD to the SHD. Then, insert the FFC LVDS and P/BD wire to the IF BD and assemble the IF BD to the SHD. Lock all PCBA screws, DP xxxx , and grounded xxxx .
4. Assemble the panel to the MF. Take the panel and insert the lamp wire into the panel. Then, assemble the MF to the panel and lock the screws to the MF. Stick adhesive tape on the little connector of the lamp wire.
5. Assemble the ASSY TRIM by inserting the LED wire into the LED BD and assembling the LED BD into the TRIM. Then, assemble the ASSY TRIM on the MF and lock the screws to the ASSY TRIM.
6. Assemble the SHD by inserting the FFC LVDS to the panel and locating the SHD on the panel. Affix Kapton tapes and conductive tapes on the FFC LVDS. Insert the big connector of the lamp wire to the P/BD and paste mylar on the SHD. Arrange and insert the LED wire into the I/F BD.
7. Assemble the SPK by attaching the SPK to the MF. Insert the wire of the SPK into the I/F BD and stick tapes to fasten the wire of the SPK on the panel. Stick tape to fasten the lamp wire.
8. Assemble the CTRL BD by assembling the FFC CTRL to the CTRL BD and attaching the CTRL BD to the RC. Stick adhesive tape to fasten the FFC CTRL on the RC.
9. Finally, assemble the RC, stand, and base. Insert the FFC CTRL to the IF BD and assemble the RC to the MF. Lock the xxxx to the RC. Then, assemble the stand and base to the monitor.
Please refer to the Acer VG270U LCD Monitor Instruction Manual for more detailed instructions and diagrams.
Add New Comment